IMPORTANT NOTE: Ensure any rebate strips or door stops are fi tted before proceeding.
For double-leaf doors, the inactive leaf must be securely fi xed in the closed position and a rebate strip fi tted to prevent
door over-travel.
100 Series strike suitable for 15mm latches, based on a 3mm door gap.
110 Series strike suitable for 18mm latches, based on a 3mm door gap.
INSTALLATION INSTRUCTIONS
100A/110A SERIES ELECTRIC STRIKE
Mark positions X and Y of door latchbolt on door jamb (see Fig. 1).
Remove the backing of supplied stick-on template, and apply to door jamb. Ensure the lines “Front face of Lock Latch” on both template
and door jamb are aligned (see Note 1).
Scribe the door jamb according to template outline (see Fig. 2).
Prepare door jamb as per appropriate installation type; for Metal Jamb refer to Fig. 3, for Wood Jamb refer to Fig. 4. Install mounting tabs
where applicable. (see Note 2).
Ensure all wiring is correctly connected and not rubbing on sharp edges or interfering with any strike mechanism.
Install the strike temporarily in position and check there is no interference between the door, strike and lock face plates, and the extension
lip of strike during door closing. Ensure the deadlatching auxiliary bolt does not enter the strike keeper area when door is closed.
Check there is no pressure on the strike keeper when door is closed.
When all above checks are complete, secure strike with appropriate screws and re-check operation.
NOTE 1 : A 1mm clearance has been designed into the template to prevent the door exerting pressure on the strike when closed.
NOTE 2 : Allow suffi cient space between the electric strike unit and jamb cut-out for the wires. Bunching of wires may cause the unit
to malfunction.
1.
2.
3.
4.
5.
6.
7.
8.
Fig. 1 - Door Frame Preparation
a
e 1
DRAWINGS NOT TO SCALE. INFORMATION IN THIS DATASHEET MAY BE CHANGED WITHOUT NOTICE.
age
100A/110A SERIES SPARE PARTS & ACCESSORIES
The following are available as optional extras:
SPARE PARTS
* When the use of extension lips is required, the standard model numbers of electric strikes must be suffi xed with “X” to denote
pre-drilled extension holes (e.g. 110X).
Align with
“Front Face
of Lock
Latch” line
on Template
y
x
y
X
X
y
or
Bevelled Face
xx
y
y
Door Edge
or
Mortice Lock
Tubular/Cylindrical
Latch
Part Number Qty Per Pack Description
220100-501 1 12 V Solenoid Coil
220100-512 1 12 V Weather Resistant Solenoid Coil
220100-502 1 24 V Weather Coil
220100-511 1 24 V Weather Resistant Solenoid Coil
220100-509 1 48 V Solenoid Coil
200100-100 5 100 Series Locking Pins, Spring and Stop Screw
200100-110 5 100 Series Weather Resistant Locking Pins, Spring and Stop Screw
200110-100 5 110 Series Locking Pins, Spring and Stop Screw
200110-110 5 110 Series Weather Resistant Locking Pins, Spring and Stop Screw
ACCESSORIES
Part Number Qty Per Pack Description
220100-506 1 100 Series 15mm Extension Lip *
220110-502 1 110 Series 15mm Extension Lip *
220100-507 1 100 Series 25mm Extension Lip *
220110-503 1 110 Series 25mm Extension Lip *
220100-508 1 100 Series 50mm Extension Lip *
220100-504 1 110 Series 50mm Extension Lip *
An ASSA ABLOY Group brand
DA0006, Issue 8: 16th Feb 2007
104.8mm
Limits of Extension Lips
59.5mm
*86mm
*123.7mm
Keeper Width
38.8mm
31.7mm
*43.7mm
NOT TO SCALE
Front Face of
Lock Latch
R 4.0mm
15mm extension lip (A),
25mm extension lip (B)
50mm extension lip (C)
available as optional extras.
C
50mm
A
15mm
B
25mm
STRIKE FACE PLATES
Fig. 2 - 100A/110A Series ANSI Face Plate Type “A” Template Outline
For a wide range of strike face plates to suit a particular application, please contact your nearest distributor.
*These dimensions have a tolerance of +0.8mm/-0
Template outline may vary depending on strike face plate used.
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern